The cost of repairing a phone or tablet after water gets into it is different.

It all depends on the damage. Only diagnostics can determine the exact price.

Even the approximate price is determined by the actual breakdown, although in this entry I will try to indicate as accurately as possible the cost of repairing a phone that fell into the water.

NOTE: the price also depends on the place where you go and sometimes it reaches thirty percent of the difference - checked

Estimated cost of repairing a phone after water ingress

Typically, the price ranges from $ 10 to $ 80. There are, of course, exceptions, but there is one more thing.

If you don't take action right away, the repair may no longer help - it's checked.

NOTE: maximum oxidation does not occur immediately, so the smartphone may work for a while - death may occur later.

Also, the cost of resuscitation after falling into the water depends on the model. After all, there is no need to prove that expensive phones use more expensive components.

Most often, repairs are required: keyboard, speaker, microphone, screen, sensors and charging.

A critical situation is the oxidation of radioelements. Recovery is not always possible then.

Also, sometimes repairs are unprofitable and pointless, and diagnostics made in some workshops are paid in others for free. However, the price for it is small, somewhere between 0.5 and 1 dollar.

Phone firmware price

NOTE: the price does not depend on the name of the phone, for example, Lenovo, Samsung Galaxy, Huawei, HTC, Asus, LG, Nokia, but only on their category.

In case of flooding, sometimes it is necessary to alter the device.

For example, flash memory is damaged, the cost of which is about $ 40 (depending on the category of the device)

The price of the firmware ranges from $ 5 to $ 10, here it also depends on the category and possibly the version.

Simple repair cost

Simple repairs are not expensive, but you will have to pay between $ 5 and $ 10. This can be, for example, cleaning from dirt.

After all, the phone does not always fall into the bathtub, where the water is clean. It can fall into a puddle where there is a solid mule at the bottom.

Corrosion cleaning cost

But this will tell you only after inspection - the corrosion is different, and if the motherboard is covered with it, then most likely they will give you the device and say goodbye.

For example, replacing a microcircuit can cost up to $ 40, and repairing broken conductors can also cost so much.

Again, a lot depends on the category, and it is as follows:

• Devices under $ 50 fall into the first category.
• To the second category up to $ 100
• Into the third category from $ 100

That's it. As mentioned above, this is just a rough estimate of some of the repair prices. Good luck.

A lot can be done through negligence. Particularly at risk are mobile devices, with which people now practically do not part. They are often dropped. And it's good if the phone falls on a soft surface. Even if you fall on the asphalt, there is a chance that nothing bad will happen. But if the device fell into a puddle, or did not even fall, but got wet in some other way, this is already unpleasant. In such a situation, you need to act quickly, without hesitation. Therefore, you need to know the sequence of actions. What to do if water gets into the phone?

What shouldn't you do?

There are some weird methods, like putting the device in a bag of rice, which will draw out all the moisture. It is also advised to completely fill the phone with alcohol. What to do if water gets into the phone? Certainly not to follow such advice. All this is ineffective, and then it will become clear why.

The most dangerous liquids for phones are sea water, water with detergent or, mind you, jam. Yes, they drop it too. And liquids containing alkali, salts and so on are also dangerous.

Even if the water that gets into the phone is distilled and does not transmit electric current, then the debris that is sure to be inside each device can lead to unpleasant consequences. What to do if water gets into the phone? Immediate action must be taken immediately. After all, even if you dry the device without disassembling it, then over time all the tracks on the board will still oxidize and collapse. A month later, irreparable problems may already begin. A recessed phone will still work, but it will not be able to live like this for a long time.

So what is the sequence of actions needed? What to do if water gets into the phone? And you need to do the following:

• Remove the back cover and remove the battery.
• Shake off all visible drops.
• Find a dry rag or towel.
• Remove the housing and remove all liquid inside the device.
• The board needs to be washed with alcohol.
• Do the same with all other metal parts (this can be done with a brush or in an ultrasonic bath).
• Dry the device for at least 12 hours.

Detailed description of actions

You can't hesitate even a second to remove the battery! What to do if water gets into the phone? You need to get it out of the water if it falls there, since even a couple of seconds is enough for a significant amount of moisture to get into the holes for the headphones and memory cards. It’s even worse if it’s water with detergent. So housewives should put their phones away while doing the laundry. The battery must be removed as soon as possible, as a short circuit may occur. In the process of disassembling the device, the SIM card and drive are removed. All this must be put on a dry towel.

Phone disassembly

Many users, of course, will carry the drowned device to a service center, but not all craftsmen make high-quality repairs to equipment. Especially if it's a wet phone. Some do only part of the repair, after which the device can work no more than a month. Therefore, it is better to understand this issue and do everything with your own hands. After all, the user himself will treat his gadget much more carefully than a master who does not care about other people's property. And with their "help" you can easily and irrevocably lose all valuable information.

First, on the Youtube site, you need to find instructions for disassembling exactly the same phone model as the user has. The video will show everything: from the type of latches to the number of loops. Sensor devices have fewer nodes.

What tools will be needed?

• Set with small screwdrivers, sprockets or hexagons. It depends on the specific model.
• A sharp scalpel, plectrum, or some other thin plate that can be used to pry on the body parts of the device.

Everything should be done slowly, very slowly and carefully. It is necessary to carefully disconnect all cables, speakers and the like.

Cleaning from the inside

This process is probably the most painstaking. It is better not to use cotton wool here, because too much lint remains from it. Better to choose cotton or napkins.

The solvent must not be used under any circumstances! In order to clean the device board, you can take ordinary ethyl alcohol from the first-aid kit. After all, it is available.

For now, we need to move the speakers, microphone and display aside. Then it will be possible to wipe only the contacts. It is not necessary to wipe the outside of the case with alcohol, as this can leave streaks and stains, which will ruin the appearance of the device. The board itself can be dipped in alcohol. All impurities and oxidations are cleared from it. If you do not do this immediately and efficiently, then after a while it will be too late, and you will need to solder it. If there is a board after cleaning with a brush, you can dip it into it.

Alcohol drying

After bathing, the board is wiped dry from alcohol. This must be done very carefully. After the liquid has evaporated, the dissolved substances should not settle on the parts. Alcohol dries very quickly, but moisture can remain under the microchips.

After all the above operations, you can assemble the phone and try to start it. Everything should work. This should save you hassle and money.

If, nevertheless, the phone does not work, then you cannot do without visiting the service center. The main thing is to choose a good master. Recommendations from other people should help in this.

Water in the sensor

Sometimes it happens that water gets into the phone screen. What to do? In most cases, it must be replaced with a new one, since even small droplets are undesirable. The cost of the screen is not very high, but you can find it in specialized stores. You can also ask for repairs there.

If a decision is made to replace it yourself, then you need to do the following:

• Disassemble the device.
• Separate the sensor itself from the screen. If there is a sticky layer, then it can be wiped off with a cotton swab soaked in nail polish remover.
• Install a store-bought sensor.

Attention, before buying it, you need to make sure that it is not a connector or a cable, as often the contacts simply deteriorate due to corrosion.

It also happens that water gets into the speaker of the phone. What to do in this case? There is no choice here: you just need to change it to a new one. The speaker can no longer be restored. What if water gets into the cell phone? What to do then? Here it is fifty-fifty: either when disassembling and drying, the moisture in it will completely dry out, or especially sensitive elements will refuse to work and you will have to carry the device to a service center, where, most likely, they will say that the camera needs to be replaced.

These are the actions that will help if the mobile phone gets into the water. What if this happens? The main thing is, don't panic. If everything is done correctly, then in a day there will be no consequences. But the best thing is to be careful and make sure that your mobile does not end up near sources of moisture.

A similar misfortune can happen to anyone, and with some it happened more than once. Someone drops their mobile phone into the sink or toilet bowl, someone washes it with clothes, and someone just spills some liquid on it.

Does the device not turn on? Do not rush to get upset, you can try to bring him back to life. We know how you can bring your drowned phone to life with a few simple steps. Nobody gives guarantees, but why not give it a try?

1. Switch off the phone. This is exactly what needs to be done right away with a device pulled out of the water. The fact is that the breakdown of the device is not due to the destructive actions of moisture, but to short circuits that appear due to it. Under no circumstances should you shake the phone, because the liquid can penetrate even deeper. If the battery can be removed from the phone, then this should be done as soon as possible. If it is not removable, then you should at least turn off the power. If it was turned off when it entered the device, do not try to turn it on for testing. It takes a couple of days to bring the phone back to normal, so get ready to go without it for a while.

2. Disassembly. Anything that can be superficially unscrewed and unscrewed on the device must be removed. This can be a back cover, SIM card, plugs. Only the main thing here is not to overdo it, otherwise the phone will be disassembled to the cogs, and then it will not be assembled. It is important to understand that a wet apparatus requires as many holes as possible to dry.

3. Drying. It is good if you have a vacuum cleaner with a nozzle in the form of a narrow tip at hand. It can be used to try to remove the maximum amount of moisture from a wet apparatus. It is best to vacuum each accessible hole for at least five minutes. As a last resort, you can also use a hairdryer to dry. However, it is important to remember that the air stream must be cold, because the warm stream can simply melt the parts. So in this case it is better to use a vacuum cleaner.

4. Drying. This step will require the affected device to dry. To do this, it is better to put the phone in a container with rice. The secret is simple - this cereal absorbs moisture well. The main thing here is to be patient and leave the device in this state for at least two days. If after that some traces of moisture remain on the phone (it may be a fogged-up screen), then you can wait another day. If the device looks normal, then you can try to turn it on.

If these steps were done correctly and in the correct sequence, then the chances are high that the phone will work as if nothing had happened.

Your question:

How to fix a phone that has been dropped?

The master's answer:

Mobile phones, which until recently were completely absent from the overwhelming majority of the population, quickly gained a foothold in the status of a basic necessity. In a hurry, on the go, pulling them out of a pocket or bag, we often drop them. What to do if the phone fell?

Naturally, each fall is different. If we dropped the phone on the rug at home, then most likely nothing bad will happen to the device.

If he fell on the sidewalk, from a height or onto the pavement, then the damage can be quite serious. As a rule, more often in such cases it gets to the display - cracks may appear on the screen, or it may even break. In addition, the case may crack.

Depending on what kind of damage happened to the phone, some parts can be replaced with your own hands by purchasing them in mobile phone stores.

But if these are deep internal deformations, then it would be better to contact a repair shop, because mobile phones are a complex electronic device.

It is not uncommon for phones to fall into water or other liquid. Sometimes this liquid becomes toilet water or, even worse, a public toilet. In this case, remove the phone as soon as possible. After that, you should wipe the case, open the phone and remove the battery. Water acts on the elements of the phone.

Next, you need to slowly disassemble the phone as much as possible. If there were impurities in the liquid, you need to rinse each part under running water. Then gently wipe them with a napkin, and prepare the phone for drying.

Do not dry your phone in the usual way - on a stove or a radiator. Such drying evaporates moisture from the surface, while leaving it in narrow, hard-to-reach places. In no case should you use a hairdryer. It is more likely to drive moisture inside, and this will inevitably lead to the fact that the metal parts are oxidized.

The best way to dry your phone is to draw moisture out of the parts. For this, ordinary rice is most suitable as an absorbent.

We pour it into a hermetically sealed container, which is the size of the phone. We place the body and all the unscrewed elements of the phone into it. Close the lid tightly and shake. We leave the container with the phone for a couple of days in order for the liquid to be completely absorbed from the surface of the elements. At the right time, we remove and blow off the parts. Putting the phone back together. Insert the battery and turn it on, the phone should work.

It happens that the phone can sometimes fall into the sink or, even worse, the toilet. You can forget your mobile phone in the pocket of your jeans that were loaded into the washing machine, and sometimes it can be damaged by someone's joke, for example, if you are pushed into the pool without warning. Caught in the rain without an umbrella? Dropped your phone in your pet's bowl? Most likely, you will have to buy a new one, but if you act quickly, then there is still a chance to save the mobile phone. This article provides some helpful tips on how to reanimate a wet phone.

Steps

The phone should be removed from the water as soon as possible. The hands-free ports, microphone opening, charging port, USB cable, and the slots between the phone and the plastic charging cover let water pass freely in a few seconds. The phone must be removed from the water and turned off immediately, as water that gets into it can lead to a short circuit.

If the phone was in the water for only a few seconds, then there may not be any consequences. Even if the phone is washed in the washing machine, there is still a chance to save it. Before buying a new phone, it is worth trying all the methods described in this article.

• If the phone has been dropped into water while connected to the charger, removing it from the water by yourself can be dangerous. Here you need the help of a professional who will take the necessary measures and do it safely (most likely, you will need to turn off the electricity throughout the house). Water is an excellent conductor of electricity, so saving your phone yourself could result in an electric shock. However, if the phone was not connected to the charger, then you can remove it yourself - you need to do this as soon as possible.
• Do not panic. If you remain calm, you will get things done quickly and correctly.

1. Immediately after removing the phone from the water, wipe it with paper towels or a soft cloth, then remove the cover from the phone and remove the battery. This is one of the most important things in a phone rescue business. Many circuits inside the phone do not suffer from moisture unless they are connected to a power source (battery) when wet.

   • To find out if your phone has really been damaged by water, you need to check the indicator in the corner of the battery hole. It looks like a white square or circle, possibly with red lines. If it turns pink, it means that the phone is damaged by water.
   • To find out how to remove the battery and find the indicator, it is best to refer to the instructions that came with the phone.

2. Remove the SIM card. Some or all of your valuable contacts (along with other data) can be saved on the SIM card. For many, the safety of contacts is much more important than the safety of the phone itself.

   • SIM cards are quite resistant to water damage. However, it should be removed and wiped dry, set aside and allowed to dry until the phone itself is ready to use.

3. It is necessary to disconnect all peripheral devices such as headphones, memory cards, as well as anything that can clog gaps, crevices and cracks in the phone (covers and protective films).

   Better to use a soft cloth or towel. If even one If a drop of water remains inside, it may destroy the phone, corroding the circuits, or a short circuit may occur. Wipe off as much water as possible to prevent it from getting inside the phone:

   • Gently wipe off any excess water on the outside. No need to shake or turn the phone over to avoid water getting inside it.
   • When using towels, paper or not, you need to make sure that fluff or wet paper does not clog up small gaps and holes in the phone. Wipe the phone gently, remove as much water as possible.
   • Rubbing the water off with alcohol will help the water evaporate from the phone surface as soon as possible.

4. Use a vacuum cleaner. If you have a vacuum cleaner handy, use it to blow out the water. To remove any remaining moisture, you need to blow through every part of the phone for 20 minutes.

   • This is the fastest method and can completely dry your phone in just thirty minutes. However, if contact with water has been enough long, this method is unlikely to help.
   • Do not put your phone too close to the hose of the vacuum cleaner, otherwise static electricity will build up, which is even worse for the phone.

5. Do not use a hair dryer to dry your phone. It may sound surprising, but using a hair dryer not recommended (not even "sparing" mode). Using a hair dryer, you can blow moisture from the surface further into the interior of the phone, this is especially dangerous for electrical components hidden deep inside the phone. And if the air from the hair dryer is too hot, then its jet can melt some parts of the phone.

   • If moisture gets inside the phone, then the chance of corrosion of individual elements and their oxidation increases, especially schemes that include minerals are at risk. Ultimately this can lead to malfunctioning of the phone.
   • There is no need to blow air into the phone, on the contrary, the air jet should blow out water. It follows from Bernoulli's law that warm dry air, moving quickly on the phone, reduces the static pressure of compressed air, which will not allow all moisture to be blown out of the phone. The main conclusion that follows from this is that you can spend several hours in a row trying to dry your phone with a hairdryer and not achieve the desired result.

6. Use a substance that can draw out moisture. An inexpensive option is to place your phone in a bowl or bag of uncooked rice overnight. Rice will absorb any remaining moisture.

   • Effectively use products that absorb moisture. One of the best remedies is rice. You need to put the phone in a plastic bag and fill it with rice, then, to create a seal, the bag must be sealed (you can use a plastic container). Also among the materials that absorb moisture is silicone gel - often found in small sachets in a box with new shoes, handbags, and so on. At the same time, those bags that have been stored in boxes with shoes or clothes for some time have probably already exhausted their absorbing properties. The phone should be left in a desiccant container at least overnight.
   • While the phone is drying, it needs to be turned over from time to time so that the water, which inevitably flows down, has a better chance of finding its way out of the phone through all kinds of cracks and holes.

7. Place the phone in a sunny place so that all openings on the phone are completely dry.

   The phone should be left on absorbent wipes or paper towels, even if it has been vacuumed or placed in a container of rice before. This will help absorb any remaining moisture from the device.

   • It is worth checking the phone, placed in a container with absorbent material, every hour for the first 6 hours. If moisture has collected on the surface, then you need to dry it again with paper towels or blow it off with a vacuum cleaner.

8. Phone check. After at least 24 hours, make sure that the exterior of the mobile phone looks dry. It is worth checking all ports, bays and slots. If your phone looks dry and clean, you can replace the battery and try turning it on. Pay attention to possible strange sounds and noises accompanying the start-up process, if any, this is a sign that the phone is not functioning properly.

   If the phone looks dry but won't turn on, then the battery may have run out of time. If the phone turns on after it has been charged, then the battery is likely damaged by exposure to water and should be replaced.

   If the charging connection also did not help turn on the phone, then you should contact the place where it was purchased. Perhaps specialists will be able to repair it. But there is no need to hide the fact that it was damaged by water - all the same, the phone has indicators that show the cause of the malfunction. The more detailed the circumstances are, the easier it will be for specialists to determine the breakdown and fix it.

   Do not try to disassemble the phone yourself. Leave it to the professionals, as such experiments can lead to short circuits or poisoning from harmful chemicals that are contained in some elements of the mobile phone.

   • If the phone turns on but malfunctions, then it is likely that moisture has damaged some elements. Remove all covers, take out the battery, memory cards and SIM card - you may find corrosion. Then it needs to be brushed off the surface of the affected parts using a clean dry brush or toothbrush. There are many instructions on YouTube on how to do this correctly.

9. Buy a protective phone case. Such a cover will protect your phone from breakage during falls, as well as from water ingress. For touchscreen phones, a protective film is a must!

• Moisture is dangerous primarily for the internal circuits of the phone. If you manage to turn off the phone before the water reaches them, then most likely it will be possible to save it!
• Sometimes in stores you can find kits designed to resuscitate a wet cell phone. It is better to purchase one in advance so as not to waste time when an emergency occurs.
• If the phone has been damaged by salt water (for example, it fell into the sea or ocean), then it is necessary to wipe it with clean water so that the salt crystals at least do not remain in the battery connector.
• Never vacuum a wet object. You may be electrocuted.
• Excessive heat can damage the phone. Most of the instructions for the phone warn against leaving the device in the car in summer or exposing it to any other heat. The most important thing is to dry your phone before charging it. Using a vacuum cleaner, you can dry the phone in just 20 minutes, while you need to blow air from all sides of the phone, constantly turning it.
• You can use a vacuum chamber if you can find one, for example, in schools and universities. Of course, hardly anyone can use the training equipment, so an agreement will have to be made first. In such a chamber, water will "boil" even at room temperature after a sufficient time, and therefore evaporate, even if it is not heated. This method will work if the phone is kept in the camera for at least 30 minutes. In this way, those parts that are difficult to access will also dry out.
• Since in this case the phone cannot be repaired under warranty, you can try to disassemble it into parts in order to dry them more efficiently. Purchase special screwdrivers, prepare a dry, clean toothbrush. Spray all parts with compressed air spray and / or vacuum cleaner for a few minutes, and then put the phone back.
• It is very important to continue to dry your phone from time to time, even if it appears to be dry enough. This is not true. Placing your phone in front of a heater or fan for an extended period of time will help it dry out better. You need to relocate the urge to use the phone to check calls, messages, or just play. It should be left alone to dry for several hours.
• Alcohol treatment of the phone is useful - you need to remove all the parts (battery, SIM cards, and so on) and put the phone face down in a container with a small amount of alcohol. This won't damage your phone, but it will help dry it out and evaporate moisture.
• Another option is to keep the phone at body temperature for several hours. That is ... closer to the body.
• Take your phone with you if you are planning an airplane flight. The very dry air in the cabin is great for drying your phone.
• When using compressed air, direct the jet not at right angles, and with some inclination, and aim for slots, slots and gaps. If the phone is cold, then it needs to be warmed up, as cold air can create excess moisture, which condenses on the elements inside. This process must be accompanied by other methods, that is, the use of a vacuum chamber or vacuum cleaner. Follow all recommendations on the compressed air bottle label, as the contents can be toxic.
• When placing the phone in rice, you should remove the cover, take out the battery, and put them in the same container, but separately.

Warnings

• Do not expose your phone to prolonged heat, if you do not want some of its parts to melt.
• Remember that most modern cell phone manufacturers put a water damage indicator that changes color depending on the presence of liquid inside the phone. This helps to determine the cause of the breakdown of the phone, since if the phone does not work due to the fact that it got into the water, they will refuse to repair it under warranty... An exception may be additional insurance of the phone against exposure to water. It is worth noting that damage indicators only change color in very high humidity conditions.
• Do not place your phone (like any other electronic or metal object) in a microwave oven. This will damage not only the phone, but also the microwave.
• Do not heat the battery, it may leak or explode. Lithium ion batteries are sensitive. If you are using a hair dryer, be sure to remove the battery before drying your phone.
• If you use alcohol, be sure to do it outside. At the same time, no heat can be applied to the phone in any form. Do not insert the battery until the smell of alcohol has completely disappeared.
• Even if the phone was dry, water could damage the internal components, causing them to corrode. The components of the phone are so compact inside the phone that even one drop of water is enough to cause a short circuit.
• To dry the phone, you need to disassemble it as much as possible. Cell phones are usually waterproof, so they can be used in light rain. But on the other hand, this means that water, once inside the phone, has little chance of finding a way out of the phone.
• The faster the phone is taken out of the water and turned off, the higher the chance to save the phone.
• Do not leave your phone wet for a long period of time. Dry it as soon as possible.
• Do not turn on your phone until you are sure it is dry. This could lead to a short circuit.

What do you need

• Moisture-wicking materials (rice or ball bags found in new shoe boxes, noodle packs, etc.)
• Towels, paper towels
• Vacuum cleaner
• A bowl
• Sealed bag or container (optional)
• Cotton fabric